专业文章翻译：热浸镀锌层涂装前表面处理
Preparing Hot Dip Galvanizing for Painting – It’s not Overly Complicated热浸镀锌层涂装前表面处理-这并不太复杂
文章来自防腐涂装良心网站KTAuniversity，原文链接 请点这里
Bare galvanizing provides excellent corrosion protection at a pH between 7 and 13, but corrosion of the zinc increases as the pH becomes more acidic (less than 7), or more alkaline (greater than 13). When galvanizing is exposed to the lower or higher pH ranges, it should be painted. Paint should also be applied when aesthetics is important, regardless of pH. Unfortunately, when galvanizing is painted, paint failures can occur (Photo 1), but they are easy to prevent through proper surface preparation.
在 ph 值为7和13的情况下, 仅凭镀锌就可以提供优异的腐蚀保护, 但锌的腐蚀会随着 ph 值变酸性 (小于 7) 或碱性 (大于 13) 而提高。 当镀锌层暴露在更低或更高的 pH 值范围内时, 应当进行涂装。 当外观比较重要时, 无论 pH 值如何, 也应该涂装。 不幸的是, 对镀锌表面涂装时, 很可能发生涂层失效 (照片 1), 但通过适当的表面处理这很容易防止。
Photo 1 – Typical failure of paint to galvanizing due to lack of surface preparation.
照片 1-由于缺乏表面处理造成的典型涂层失效。
Surface preparation is the key to assuring successful coating adhesion and performance. The extent of preparation required depends on the answers to these four questions:
Was the galvanizing passivated?
Is the galvanizing new?
Is the galvanizing partially weathered?
Is the galvanizing aged?
表面处理是保证涂层附着力和性能的关键。所需处理的程度取决于对以下四个问题的回答:
镀锌层钝化处理了吗？
镀锌层是新的吗？
镀锌层是否部分风化？
镀锌层是否老化？
Passivating Treatments – Passivation is a common practice used at the time of galvanizing to reduce the formation of white storage stain. Unfortunately, passivating treatments applied to galvanizing (especially chromate treatments) can interfere with the adhesion of coatings. If the galvanized steel is going to be painted, the galvanizer should be notified in advance, so that the passivation step can be eliminated. Frequently, however, parts have already been galvanized and the user does not know whether a treatment was applied. When in doubt, the surface should be tested. A suitable procedure is provided in SSPC-SP16, Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals.” Section 4.3.3 of the standard offers the following:
钝化处理 – 钝化是镀锌时常用的一种方法，以减少镀锌件储存时白锈印迹的形成。不幸的是，对镀锌件的钝化处理(特别是铬酸盐处理)会影响涂层的附着力。如果镀锌件要涂装，应提前通知镀锌人员，以便取消钝化步骤。然而，实际情况通常是部件已经镀锌完成但用户不知道是否进行了钝化处理。如有疑问，应对表面进行测试。SSPC - SP16中提供了一个合适的程序，即“涂装和未涂装镀锌件、不锈钢和有色金属表面的扫砂处理标准。” 该标准第4.3.3节规定如下：
If all three areas turn black immediately, there is no passivation on the surface. If the first area does not turn black within 10 seconds and the second and third areas turn black immediately, there is no passivation on the surface with the possible exception of light oil. If the first and second areas do not turn black within 10 seconds and the third area turns immediately, a passivator of some type is present.
If it is present, mechanical cleaning is typically required to remove it, although some of the etching/cleaning solutions discussed below suggest that they will also remove some treatments. Before using them, it is recommended that the etching cleaner be applied to discrete areas followed by the testing described above to determine if the treatment is removed. If the project schedule permits, weathering of 12 to 18 months prior to painting, should also eliminate any treatment that may have been present.
如果3个区域均立刻变黑，则表面没有钝化处理。如果第1个区域没有在10秒内变黑，而第2和第3区域立即变黑，则表面没有钝化处理，但可能有轻微的油渍存在。如果第1和第2区域没有在10秒内变黑，而第3区域立即变黑，则表面有过钝化处理。
如果检测有过钝化处理，则通常需要机械工具来清理，尽管后面提到的一些蚀刻/清洗液也能去除某些钝化层。如果使用蚀刻清洗液，建议先在小块区域试验，随后进行上述测试，以确定是否去除了钝化层。如果项目进度允许，涂装前风化了12至18个月的构件也应去除可能存在的钝化层。
New and Partially Weathered Galvanizing – If the age of the galvanizing is less than approximately 48 hours, it may be possible to coat it as is, but if it is weathered between a couple days and approximately one year (termed partially weathered), surface preparation will be required. Two methods that are commonly used to prepare the galvanizing are cleaning/etching with a phosphoric acid/detergent blend and abrasive blast cleaning.
Etching solutions are used to clean, dull, and roughen the surface for proper coating adhesion. The solution is applied to the surface, typically scrubbed with a synthetic abrasive pad, thoroughly rinsed, and force dried. Examples of solutions can be found in the Master Painters Institute (MPI) qualified products list #25, Cleaner, Etching, for Galvanized Metal ( http://www.specifypaint.com/APL/paintinfo_APL_new/MpiNumber.asp?ID=25000 ).
新的和部分风化的镀锌层 – 如果镀锌时间小于约48小时，可以直接涂装，但如果镀锌层经过在几天至约一年之间的风化(称为部分风化)，则需要进行表面处理。通常用于镀锌件的两种表面处理方法是喷砂清理和用磷酸/洗涤剂混合物进行清理/蚀刻。
蚀刻清洗液用于表面清理、表面暗化和粗糙化以获得适当的涂层附着力。将溶液施加到表面上，通常用合成研磨片研磨，彻底冲洗，并烘干干燥。溶液种类可在“Master Painters Institute ( MPI )”认证产品列表#25“镀锌金属的蚀刻清洗液”中找到。( http://www.specifypaint.com/APL/paintinfo_APL_new/MpiNumber.asp?ID=25000 )
Abrasive blast cleaning is performed according to SSPC-SP16. Excerpts from a few paragraphs of the standard describing the cleaning of bare, uncoated metal (galvanizing) are repeated below. The sentences that were redacted address the criteria for any paint remaining on the surface, which is not applicable to this article.
喷砂清理根据SSPC - SP16进行。以下是标准中描述清理裸露未涂装金属(已镀锌)的几段摘录。节略的部分是关于表面残留油漆的标准，不适用于本文因此省略。
Paragraph 4.3.1 of the standard requires the removal of wet storage stain by means other than blast cleaning since the “dwell time” required to remove it by blast cleaning can damage the galvanizing. Other methods are addressed in a non-mandatory Appendix. Appendix Section A3 indicates that salts from wet storage stain can be removed with a nylon brush and water, or a dilute solution of acetic or citric acid, lime juice, or white vinegar, followed by rinsing with a large amount of water.
Appendix Section A8.1 indicates that to reduce the risk of damage, blast cleaning is done with relatively low nozzle pressures (A8.2) and a softer abrasive with a Mohs hardness of 5 or less (A8.1.1.).
Appendix Section A9 recommends that the thickness of the galvanizing be measured before blast cleaning and again after blast cleaning to confirm that it meets the specified thickness. The thickness requirements may be found in the procurement documents, or as required in ASTM A123, Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products, or ASTM A153/153M, Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware.
The Appendix (A9.2) cautions that in the presence of moisture, zinc oxides can form quickly on the surface after preparation, so it should remain dry, and painted as soon as possible. The same recommendations for a minimum 5°F (3°C) spread between surface temperature and dew point temperature when preparing steel (steel temperature being the higher of the two), also apply to galvanizing.
该标准第4.3.1段要求通过喷砂清理以外的方式清除储存时产生的白锈印迹，因为喷砂清理白锈印迹所需的“停留时间”可能会损坏镀锌层。其他方法在非强制性附录中讨论。附录部分A3指出，储存时产生的白锈印迹可以用尼龙刷和水，或乙酸或柠檬酸、柠檬汁或白醋的稀溶液除去，然后用大量水冲洗。
附录部分A8.1指出，为了降低锌层破坏风险，喷砂清理采用相对较低的喷嘴压力( A8.2 )和莫氏硬度为5或更低的较软磨料( A8.1.1 )。
附录A9建议在喷砂清理前和喷砂清理后测量镀锌层厚度，以确认其符合规定膜厚。厚度要求见采购文件，或ASTM A123《钢铁制品镀锌(热浸镀锌)标准规范》或ASTM A153/153M《钢铁五金件镀锌(热浸镀锌)规范》。
附录( A9.2 )警告称，在潮湿条件下，喷砂清理后会在表面会迅速形成锌氧化物，因此应保持干燥，并尽快涂装。与钢结构表面处理相同，镀锌层表面处理时同样建议表面温度超出露点温度至少5°F ( 3°C )。
Aged Galvanizing – When galvanizing has weathered for 12 to 18 months, the surface will have oxidized and can often be prepared for painting by pressure washing alone. The key is to remove surface dirt and debris as well as zinc salts and confirm that the surface is dull (photo 2).
镀锌层老化 – 当镀锌层已经风化12至18个月时，表面将被氧化，并且通常只需要高压清洗处理就可以准备涂装。关键是清除表面污物和锌渣以及锌盐，并确认表面暗化(图2 )。
Photo 2 – Exterior surfaces of the galvanizing have weathered and can likely be painted after pressure washing to remove the salts, but note the lack of oxidation and the visible spangle in the in the protected area (red arrow). A test patch should be applied to determine if the adhesion is adequate without roughening and dulling the surface.
图2– 镀锌层的外表面已经风化，可以在高压清洗除去盐分后进行涂装。但请注意保护区(红色箭头)内氧化物不多，有可见亮色的金属锌，应在该区域小范围涂漆测试，以确定未粗糙暗化的表面涂料附着力是否足够。
Depending on the condition of the steel, 3,000 psi with a rotating tip may be adequate, but it’s best to apply a test patch of the coating after cleaning and check the adhesion to make certain. If there is any doubt regarding the adhesion of the coating, either of the methods described above for partially weathered galvanizing (etching cleaner or SP-16 Brush-Off Blast) should be used.
根据钢材（表面高压冲水）的经验，旋转喷嘴的压力在3000psi（约20MPa）应该足够，但最好在锌层表面高压冲水后小范围涂漆测试，并检查附着力以确保合格。如果对涂层的附着力有任何疑问，则应使用上述部分风化后镀锌层的任一表面处理方法(蚀刻清洗液或SP-16扫砂)。
Conclusion – Most coating failures on galvanizing are the result of poor adhesion of the coating to the galvanizing. Poor adhesion is typically caused by a lack of roughening of the smooth galvanizing, an abundance of zinc salts beneath the coating film, or the presence of a passivating treatment that inhibits adhesion of the coating. When properly prepared, coatings will adhere well to galvanizing and improve the aesthetics and corrosion protection afforded by the galvanizing. This article described a few common methods or preparing galvanizing for painting. Other methods are described in:
ASTM D6386, Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting
ASTM D7396, Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting
结论 – 镀锌过程中的大多数涂层失效是由于涂层与镀锌层的附着力差造成的。附着力差通常是由于光滑镀锌层的粗糙度不足、涂层下面锌盐的大量存在或抑制涂层粘附的钝化处理而引起的。经过适当的涂装前表面处理，涂层将很好地粘附到镀锌层上，并改善镀锌层的美观性和防腐性。本文介绍了几种常用的涂装前镀锌层表面处理方法。其他方法记录于如下标准:
ASTM D6386, 镀锌(热浸镀锌)钢铁制品和五金件涂装前表面处理的标准操作规程
ASTM D7396, 新的连续镀锌钢材涂装前表面处理的标准指南
原文作者介绍：
Ken Trimber is the President of KTA-Tator, Inc. He is Chairman of the SSPC Surface Preparation Committee and the SSPC Visual Standards Committee, as well as a member of the SSPC Standards Review Committee and ASTM DOl responsible for developing, reviewing and approving standards like the ones described in this article. He can be reached at [email protected]
ken Trimber，KTA-Tator公司的总裁，SSPC表面处理委员会和SSPC目视标准委员会主席，SSPC标准审查委员会和ASTM DOl成员，负责制定、审查和批准类似文中所述的标准。作者邮箱地址 [email protected]
绛旓細缁忚繃閫傚綋鐨勬秱瑁呭墠琛ㄩ潰澶勭悊,娑傚眰灏嗗緢濂藉湴绮橀檮鍒伴晙閿屽眰涓,骞舵敼鍠勯晙閿屽眰鐨勭編瑙傛у拰闃茶厫鎬с傛湰鏂囦粙缁嶄簡鍑犵甯哥敤鐨娑傝鍓嶉晙閿屽眰琛ㄩ潰澶勭悊鏂规硶銆傚叾浠栨柟娉曡褰曚簬濡備笅鏍囧噯: ASTM D6386, 闀閿(鐑蹈闀閿)閽㈤搧鍒跺搧鍜屼簲閲戜欢娑傝鍓嶈〃闈㈠鐞嗙殑鏍囧噯鎿嶄綔瑙勭▼ ASTM D7396, 鏂扮殑杩炵画闀閿岄挗鏉愭秱瑁呭墠琛ㄩ潰澶勭悊鐨勬爣鍑嗘寚鍗楀師鏂囦綔鑰呬粙缁: Ken ...
绛旓細鐑蹈闀閿鏄竴涓繃绋,閽㈠拰閾佸彲浠ユ不鐤,浠ュ厤鐢熼攬銆傛湰璐ㄤ笂,杩欏寘鎷蹈娓鏂囩珷浠ュ寲瀛︽竻娲楄〃闈㈡垚娴存恫涓庨搧閿岀殑鍙嶅簲,褰㈡垚涓灞傘備笉鍙樼殑鍘熷垯,鐑蹈闀閿岀涓娆℃垚涓鸿锤鏄撹秴杩150骞村墠,浣嗘槸澶ч噺鐨勭爺绌舵柟闈㈢殑杩囩▼浣垮緱闀閿屼粖澶╂湁techincally鍏堣繘鐨勫伐涓氥傝嚜浠庨摳閫犻攲涓嶈兘涓庨搧鎴栭挗闀挎弧浜嗚涧鏈烘补,鎴栬呮槸闀閿屽繀椤诲厛鍑嗗娓呮礂杩囩▼鐑蹈...
绛旓細鐑蹈闀閿锛堣嫳鏂囷級锛=== Hot-dip Zinc Electroplating 鎴 Hot-dip Zinc Plating === 鍙傝冭祫鏂欙細http://www.forum.moonlightchest.com
绛旓細鐑晙閿鍖呮嫭鐑蹈閿鍜岀儹娓楅攲锛屽叾甯歌鐨勫姞宸ユ柟娉曟槸鎶婂緟闀閿岀墿娴稿叆閿屾恫姹犱腑锛岀敱浜庝笌閽㈤搧宸ヤ欢浜х敓娓楀叆灞傦紝涓旈晙灞傝緝鍘氾紝鎶楅攬铓鑳藉姏寮 銆
绛旓細3锛 鎵鏈夋鏋舵涓轰綆纰抽挗鐑蹈闀閿锛闀閿屽眰鍘氬害涓86寰背锛岀鍚圢F EN 1461 鏍囧噯锛4锛 鐒婇亾蹇呴』涓鸿繛缁剨閬撳苟涓旂剨閬撴埅闈㈠憟鍦嗛紦褰紝鐢辫祫鏍肩剨宸ユ搷浣滅剨鎺ワ紱5锛 妗嗘灦鍚勮竟閽荤洿寰勪负15mm鐨勫瓟锛岀敤浜庡悓鍦伴潰缁勪欢瀹夎锛6锛 鏉嗕欢鐨勪袱绔捇鐩村緞涓18mm鐨勫伐鑹哄瓟锛屼互鍔╀簬闀閿屼綔涓氭椂鐢紱7锛 鑻ヨ姹傚瓟寰勫ぇ浜24mm鏃讹紝杩欎簺瀛...
绛旓細鍖栧杞寲灞(Chemical Conversion Coating) 閽㈤搧鍙戣摑(Blackening),淇楃О鈥濆彂榛戔滈挗閾佺７鍖(Phosphating) 閾吀鐩愬鐞(Chromating) 閲戝睘鏌撹壊(Metal Colouring) 娑傝(Paint Finishing),鍖呮嫭鍚勭娑傝濡傛墜宸ユ秱瑁呫侀潤鐢垫秱瑁呫佺數娉虫秱瑁呯瓑 鐑蹈闀(Hot dip) 鐑蹈闀閿(Galvanizing),淇楃О"閾呮按" 鐑蹈闀閿(Tinning) PVD 鐗╃悊姘旂浉娌堢Н...
绛旓細3.2 涓鐑蹈闀閿鐨勫姣斾紭鍔 鐑蹈闀閿屽伐鑹虹殑闀閿屽眰,鏄敤浜庨挗閾佸熀鏈暱鏈熸埛澶栭槻鑵愯殌闀灞傚伐鑹,杩欑宸ヨ壓鐢ㄥ湪澶у瀷閽㈤搧浠(杈撶數閾佸銆佸伐绋嬮挗缁撴瀯绛)闀閿岄槻鑵愪笂,涓嬪璐ㄧ枒:浣嗗湪鎴峰浣跨敤绱у浐闆朵欢鐨勭儹闀娴搁攲涓,鍥藉唴宸ヨ壓杩囩▼瀹炴柦銆佸熀鏈槸鎵嬪伐鎿嶄綔,鍔犱笂鐑蹈闀閿屽伐鑹鸿繃绋嬬殑鐗瑰緛,涓庢満姊伴晙閿屽伐鑹虹殑鐗圭偣姣旇緝,灏卞憟鐜板嚭宸ヨ壓搴旂敤鐨勪紭鍔ｉ棶棰...
绛旓細SECD锛歋锛歴teel(閽) E锛歟lectrolytic(鐢甸晙) C锛歝lod D锛歞eep drawn 鍐烽棿鍘嬪欢娣辨媺鐢甸晙閽㈡澘 SECE锛歋锛歴teel(閽) E锛歟lectrolytic(鐢甸晙) C锛歝lod E锛歞eep drawn extra 鍐烽棿鍘嬪欢娣辨繁鎷夌數闀閽㈡澘 SECC-K2锛欿2涓虹鎴峰埗閽㈡墍瀵硅〃闈㈣愭寚绾圭數闀閿閽㈡澘鐨勮涓氭爣鍑嗕唬鍙蜂箣琛ㄧず锛屽叾琛ㄩ潰娑備负鏈夋満娑傚眰銆係ECC-KS锛...
绛旓細鐑蹈闀閿閽㈠嵎鏄寚灏嗙儹杞ч吀娲楁垨鍐疯涧鍚庝箣鍗婃垚鍝侊紝缁忚繃娓呮礂銆侀鐏紝娴稿叆娓╁害绾460掳C鐨勬憾铻嶉攲妲戒腑锛岃屼娇閽㈢墖闀涓閿屽眰锛屽啀缁忚皟璐ㄦ暣骞冲強鍖栧澶勭悊鑰屾垚銆係GCC鏉愭枡姣擲ECC鏉愭枡纭佸欢灞曟у樊(閬垮厤娣辨娊璁捐)銆侀攲灞傝緝鍘氥佺數鐒婃у樊銆傛姌鍙犫拫涓嶉攬閽US301 Cr(閾)鐨勫惈閲忚緝SUS304浣庯紝鑰愯殌鎬ц緝宸紝浣嗙粡杩囧喎鍔犲伐鑳借幏寰...
绛旓細浠ヤ笅鏄垜鐨勬瘯涓氳鏂囪姹傦紝鍏ㄥ浗鍚勪釜瀛︽牎鍏跺疄閮芥槸涓鏍风殑.涓銆佸唴瀹硅姹 姣曚笟璁捐鎶ュ憡姝ｆ枃瑕佹眰锛氾紙涓锛夌悊銆佸伐绉戠被涓撲笟姣曚笟璁捐鎶ュ憡姝ｆ枃鍐呭搴斿寘鎷細闂鐨勬彁鍑猴紱璁捐鐨勬寚瀵兼濇兂锛涙柟妗堢殑閫夋嫨鍜屾瘮杈冭璇侊紱鏍规嵁浠诲姟涔︽寚鍑虹殑鍐呭鍜屾寚鏍囪姹傚啓鍑鸿璁¤繃绋嬨佽棰樻墍娑夊強鍏冧欢缁撴瀯鍜岀浉鍏冲弬鏁扮殑璁捐璁＄畻锛屾湁鍏冲熀鏈師鐞嗙殑璇存槑涓...
